Resources and Services
Quick Tips
Tip: Types of Geo Thermal Heating Systems
Need help? Here’s a breakdown of the different types of geothermal systems.
Geothermal systems use the earth as a heat source and heat sink. A series of pipes, commonly called a “loop,” connect the geothermal system’s heat pump to the earth. There are two basic types of loops: closed and open.
Open Loop Systems
The simplest of geothermal systems. Used successfully for decades, ground water is drawn from an aquifer through one well, passes through the heat pump’s heat exchanger, and is discharged to the same aquifer through a second well at a distance from the first.
Generally, two to three gallons per minute per ton of capacity are necessary for effective heat exchange.
Since the temperature of ground water is nearly constant throughout the year, open loops are a popular option in areas where they are permitted.
Closed Loop Systems
These have become the most common. When properly installed, they’re economical, efficient, and reliable. Water (or a water and antifreeze solution) is circulated through a continuous buried pipe. The length of loop piping varies depending on ground temperature, thermal
conductivity of the ground, soil moisture, and system design. (Some heat pumps work well with larger inlet temperature variations, which allows marginally smaller loops).
Horizontal Closed Loop
Generally most cost-effective for small installations, particularly for new construction where sufficient land area is available. These installations involve burying pipe in trenches dug with back-hoes or chain trenchers. Up to six pipes, usually in parallel
connections, are buried in each trench, with minimum separations of a foot between pipes and ten to fifteen feet between trenches.
Vertical Closed Loops
are preferred in many situations. Vertical loops are also used where the soil is too shallow for trenching and minimize the disturbance to existing landscaping. For vertical closed loop systems, a U-tube (more rarely, two U-tubes) is installed in a well drilled 100 to 400
feet deep. Because conditions in the ground may vary greatly, loop lengths can range from 130 to 300 feet per ton of heat exchange. Multiple drill holes are required for most installations, where the pipes are generally joined in parallel or series-parallelconfigurations.
Slinky loops
Increasingly, coils—overlapping coils of polyethylene pipe—are used to increase the heat exchange per foot of trench, but require more pipe per ton of capacity. The trench length decreases as thenumber of pipes in the trench increases—or as Slinky coil overlap
increases.
Pond Closed Loops
A special kind of closed loop system. Where there is a pond or stream that is deep enough and with enough flow, closed loop coils can be placed on the pond bottom. Fluid is pumped just as for a conventional closed loop ground system where conditions are suitable, the economics are very attractive, and no aquatic system impacts have been shown.
More Popular Entries
Additions & Remodels
Soundproofing Techniques
Small Kitchen Projects Can Make a Big Difference
Easy Financing Options for Remodeling
Agents (Real Estate), Appraisers & Home Inspectors
Home Inspections
The Final Walk Through
Townhouses
Appliances
Installing Appliances
Selecting Major Appliances
Repair Dishwasher and Water Damage
Builders (New Homes), Architects & Designers
Conventionally Framed Home Builder
Checklist: Preventing Builder Fraud
Workout Room
Carpentry & Cabinets
Tip: Dealing with Dryrot
Cabinet Options
Tip: Repair Laminate Countertops
Cleaning Services
The Importance of Air Duct and Vent Cleaning
Prevent Wear with Fabric Protection
Ways to Clean Your Carpet
Concrete, Brick & Stone
Installing Concrete
Tip: Repair Concrete Steps
Wunderbar Rebar!
Consumer Guides
Time for a New Roof?
Preparing a House for Sale
Upgrading Your Electrical System
Design Ideas
Drywall Textures and Styles
Prefinished vs. Unfinished Wood Flooring
Asphalt Shingles: The Wood and Tile Alternative
Electrical, Telephone & Data
Whole House Fans
Tip: Repair Home Entertainment Equipment
Convenient Electrical Fixtures
Expert Advice
Install a Front Door
Insulating a Crawl Space
Air Quality
Flooring
Hardwood Inlay
Cleaning Hardwood Floor Inlay
Steam Cleaning Grout
Handyman Services
Avoiding Home Repair Rip-offs
Some Assembly Required
The Benefits of Weatherstripping
Heating & Cooling
Tip: Types of Geo Thermal Heating Systems
Heat Pumps
Environmentally Friendly Solar Heat
Home Construction
More Return on Your Home Improvement Investment
Tip: Panelized Homes
Do Homework Before Building a New Home
Landscape, Decks & Fences
Asphalt Paving
The Attention Your Landscape Needs
Preparing Your Yard for Winter
Moving & Storage
Some Assembly Required
Preparing a House for Sale
Stowing it Away: Where to Put It
Other Services
Tip: Fire Protection or Prevention
Simple Ways to Keep Your Children Safe
Wet Basements
Painting & Staining
Tip: Roller Marks - Interior Paint
The Right Tools for Interior Painting
The Basics of Interior Painting
Plumbing
Safe Drinking Water
The Importance of Clean Water
Find a Water Treatment Service
Quick Tips
Tip: Cleaning Fireplace Burns
Tip: Repair or Maintain Sprinkler Systems
Checklist: Basic Lawn & Landscape Care
Roofing, Siding & Gutters
Install Roofing Snow Melt Protection
Install or Replace Flat Roofing
Modern Roofing Options
SP Feature Article
The Internet Will Change the Buying of Services
Walls & Ceilings
Techniques for Wall Covering Removal
Create a Turn-of-the-Century Look With Metal Ceilings
Acoustic Ceiling Cleaning
Windows & Doors
Basic Door Lock Information
Installing the Correct Blinds or Shades
Choosing Between Blinds or Shades